Polaris
Wear Rod Application Chart |
 |
 |
To prevent cross-threading, rotate the nut
counter-clockwise until you feel the end of the nut's thread fall over the end
thread of the bolt. Then, turn clockwise to tighten.
Do not over tighten nuts! Tighten only until firmly snug. This is
especially important when working with plastic skis. They always have a
cushioned feel to them, unlike steel skis which provide a dead stop to the nut.
We use 5/16" x 18 bolts because these are all that is necessary - strength-wise. Having more than one bolt only helps keep the host bar straight. Also, this
allows the easiest installation without any need to drill the skis or use a
hammer. It is not
the size of the bolts, but the number and location that is important. Easy installation
To specify Triple Point Carbide models, replace the Good 'n Ugly prefix C or CH with TP
For example: C-B13 becomes TP-B13 or CH6-B12 becomes TP6-B12
| Pricing Info |
4" |
6" |
8" |
| Triple Point Carbide |
NA |
TP6
|
TP8 |
| Good 'n Ugly - single carbide |
C |
CH6 |
CH8 |
Model numbers shown below are for Good n Ugly single carbides only.
| Model/Year |
4" |
6" |
8" |
| All Models 71-85 |
C-H02 (off season only) |
X |
X |
| All Indy's 86-87 (Except
below) |
C-H03 (off season only) |
X |
X |
| Sport 87 |
C-H04 |
CH6-H04 |
CH8-H04 |
| All Indy's
88-04
(steel skis) |
C-H04 |
CH6-H04 |
CH8-H04 |
| Ultra Lite (SLP) |
C-H04P |
CH6-H04P |
CH8-H04P |
| All Plastic Skis
(except below) |
C-H04P |
CH6-H04P |
CH8-H04P |
| Sidehiller 2
03-04 |
C-H06 |
CH6-H06 |
CH8-H06 |
| "Easy Steer"
Replacement Ski |
|
X |
X |
RMK 600 / 700 /
800 03-04 (Accu-Trak)
(Except Sidehiller 2 skis)
Accu-Track
wear rods are only a temporary and superficial fix for darting because they
do not address the causes of darting.
We suggest using a
H04P rod with 3/8" Ski Savers. The back three bolts do line up. To get
proper wear pattern, add a 3/16" to 1/4" shim to the bottom back of the
rubber stop.
Darting Solutions |
C-H04P |
CH6-H04P |
CH8-H04P |
SKS 700 / 800
03-04 (Accu-Trak)
(Except Sidehiller 2 skis)
Accu-Track
wear rods are only a temporary and superficial fix for darting because they
do not address the causes of darting.
We suggest using a H04P
rod with 3/8" Ski Savers. The back three bolts do line up. To get proper
wear pattern, add a 3/16" to 1/4" shim to the bottom back of the rubber
stop.
Darting Solutions |
C-H04P |
CH6-H04P |
CH8-H04P |
Product
enhancements
Home |
Polaris Wear Rod Drawings | Ski Savers Chart | Trail Grabbers Chart
Wear Rod Main Page | Site Map
Contact Us
Copyright © 1999-2016 Bergstrom Skegs, Inc.
All
rights reserved. |